Brake problem?? Need help.

97Whitesnake · 06-08-2007, 01:05 AM

My car started making a shreaking sound during low speed left turns a while back. Upon inspection of the drivers side rear brake I noticed that the rotor is rubbing on the bracket that the caliper is mounted on. The outer edge of the rotor is now rounded. Any ideas??
Thomas

**cobrabitn** · 06-08-2007, 07:22 AM

Soounds like your rotor is warped. Raise the vehicle, take off the wheel, and visually inspect the rotor for trueness by turning it. If it wobbles or moves from side to side, it is time for a new rotor.

dewone · 06-08-2007, 04:10 PM

Check the wheel bearings also. As well as the caliber mounts. Sounds like there may be some slop in there for it to only rub while turning. .02 good luck

johnbasf · 06-08-2007, 08:06 PM

Quote:

Originally Posted by dewone

Check the wheel bearings also. As well as the caliber mounts. Sounds like there may be some slop in there for it to only rub while turning. .02 good luck

I second the wheel bearing theory.

97Whitesnake · 06-08-2007, 08:47 PM

I dont think its the rotor... ther wear is the same all the way around. The rotor is definetely rubbing on the caliper mount and it is only during left cormers. I had suspected that there my be too much lateral slop in the rearend so I'll look into the bearings... that sounds as if it might be the problem.
Update... I inspected the set of rotors that I took off a couple of months ago and the one from the side in question is also round a little bit. This makes me lean more towards bearings.

97Whitesnake · 06-10-2007, 05:03 PM

Took a look at the bearings last night. After we took the cover off the pumpkin and drained the fluid we noticed that there was a lot of play in the rearend. If I grabbed the ring gear it will move side to side over a half of an inch. Should there be this much play in the rearend?

97Whitesnake · 06-23-2007, 06:01 PM

Problem solved,
When we took the diff housing out it was easy to see what was wrong. One of the housing bearing was completelly shot. It was all mangled and looked as if it would not was another mile in the car... all the shims were mangled too. The machine shop that took the bearings of and pressed on new ones said the bearing fell apart in their hand when they took it off. I had been thinking that my tranny was making LOUD noises and I was getting ready to switch it out bu it was the rearend making all the noise. Also switched out the stock radiator for an 03 unit and my cooling issues look to be fixed... I can use the AC now!!

Almost ready for VIR!!

06-08-2007, 01:05 AM	#1
97Whitesnake Registered User Join Date: Jun 2001 Location: Columbia Posts: 154	Brake problem?? Need help. My car started making a shreaking sound during low speed left turns a while back. Upon inspection of the drivers side rear brake I noticed that the rotor is rubbing on the bracket that the caliper is mounted on. The outer edge of the rotor is now rounded. Any ideas?? Thomas __________________ Thomas Bramblett 97 Crystal White #552 Born 19Sept96 FRPP 4.10s, Motorsports Pullies, Borla/SVO side exhaust, Nitto Dr's, Steeda Tri-ax/MGW handle,Cobra R's, Home Depot cold air kit, FR500 steering wheel,BBK H-pipe.. I think thats it....13.45@104mph

06-08-2007, 07:22 AM	#2
cobrabitn Dr Jekyll on the street, Mr Hyde on the track Join Date: Jun 2001 Location: Rock Hill SC Posts: 14,649	Soounds like your rotor is warped. Raise the vehicle, take off the wheel, and visually inspect the rotor for trueness by turning it. If it wobbles or moves from side to side, it is time for a new rotor. __________________ Cobrabitn 2016 Ruby Red Metallic with Caribou accent F-350 Crew Cab Stump Puller! 6.7 Diesel Automatic with Chrome Package, Off Road Package, 3.55 Locking axles, and Ultimate Lariat Interior Trim Package! 2017 Shelby GT350 Coupe - track car! Mods: JLT True Cold Air oil catch can 2009 Vista Blue Shelby GT 500 Coupe - Garage Queen Tinted Windows JLT True Cold Air Kit Pro-Dyno Tune 526 rwhp - 511 rwtq 1994 Rio Red Indy Pace Car #22 "Runabout" Snake in the grill MGW shift knob 1996 SVT Cobra Wheels 1969 New Lime Mustang Mach 1 Sportsroof - Second owner - bone stock with shaker. One SVT Cobra, one Shelby GT500, one 69 mach 1, and a Shelby GT350 is better than nothing! Custom Data Plates for your Mustang or Ford! Buy "Cool Merchandise" at Data Plates Plus www.dataplatesplus.com See my MSR Video here!

06-08-2007, 04:10 PM	#3
dewone Registered User Join Date: Aug 2004 Location: West Chester OH Posts: 380	Check the wheel bearings also. As well as the caliber mounts. Sounds like there may be some slop in there for it to only rub while turning. .02 good luck __________________ Mods: BBK Long Pipe Headers (Ceramic), Under Pulley Kit, Twin 65mm Throttle Body. Roush Side Pipes. Magna Flow Muffs, & Car Sound Hy Flow Cats Stainless, Husker Stainless X Pipe. KN FIPK. Pro 5.0 Shifter . Stainless Cobra inserts, Cobra emblem in grill 291.2 RWHP #5708 of 6961 1930 Buick 30-57 1991 F-150

06-08-2007, 08:47 PM	#5
97Whitesnake Registered User Join Date: Jun 2001 Location: Columbia Posts: 154	I dont think its the rotor... ther wear is the same all the way around. The rotor is definetely rubbing on the caliper mount and it is only during left cormers. I had suspected that there my be too much lateral slop in the rearend so I'll look into the bearings... that sounds as if it might be the problem. Update... I inspected the set of rotors that I took off a couple of months ago and the one from the side in question is also round a little bit. This makes me lean more towards bearings. __________________ Thomas Bramblett 97 Crystal White #552 Born 19Sept96 FRPP 4.10s, Motorsports Pullies, Borla/SVO side exhaust, Nitto Dr's, Steeda Tri-ax/MGW handle,Cobra R's, Home Depot cold air kit, FR500 steering wheel,BBK H-pipe.. I think thats it....13.45@104mph

06-10-2007, 05:03 PM	#6
97Whitesnake Registered User Join Date: Jun 2001 Location: Columbia Posts: 154	rearend play? Took a look at the bearings last night. After we took the cover off the pumpkin and drained the fluid we noticed that there was a lot of play in the rearend. If I grabbed the ring gear it will move side to side over a half of an inch. Should there be this much play in the rearend? __________________ Thomas Bramblett 97 Crystal White #552 Born 19Sept96 FRPP 4.10s, Motorsports Pullies, Borla/SVO side exhaust, Nitto Dr's, Steeda Tri-ax/MGW handle,Cobra R's, Home Depot cold air kit, FR500 steering wheel,BBK H-pipe.. I think thats it....13.45@104mph

06-23-2007, 06:01 PM	#7
97Whitesnake Registered User Join Date: Jun 2001 Location: Columbia Posts: 154	Problem solved, When we took the diff housing out it was easy to see what was wrong. One of the housing bearing was completelly shot. It was all mangled and looked as if it would not was another mile in the car... all the shims were mangled too. The machine shop that took the bearings of and pressed on new ones said the bearing fell apart in their hand when they took it off. I had been thinking that my tranny was making LOUD noises and I was getting ready to switch it out bu it was the rearend making all the noise. Also switched out the stock radiator for an 03 unit and my cooling issues look to be fixed... I can use the AC now!! Almost ready for VIR!! __________________ Thomas Bramblett 97 Crystal White #552 Born 19Sept96 FRPP 4.10s, Motorsports Pullies, Borla/SVO side exhaust, Nitto Dr's, Steeda Tri-ax/MGW handle,Cobra R's, Home Depot cold air kit, FR500 steering wheel,BBK H-pipe.. I think thats it....13.45@104mph

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search